Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    www.aztecharmory.ca
    Join Date
    Dec 2014
    Location
    Penticton BC
    Posts
    330

    Quarter Circle 10

    We now have access to QuarterCircle10 products available for import into Canada.

    We are working on getting them loaded into our catalog, but here's a link to their site for now: http://www.qcircle10.com/

    You can order anything you see there through us, just give us a call or email and let us know what you need. Prices will be the same as what you see on their site.

    Thanks for your interest and let me know if you have any questions.

  2. #2
    GOC Co-Founder jwirecom109's Avatar
    Join Date
    Mar 2012
    Location
    South Central Rural Alberta
    Posts
    11,388
    So the Colt 1911 Lower is for 1911 magazine design?


    Welcome to GOC, Site for honest, hardworking Canadians, that own firearms.

  3. #3
    www.aztecharmory.ca
    Join Date
    Dec 2014
    Location
    Penticton BC
    Posts
    330
    They use Colt SMG magazines... basically an Uzi mag modified to hold the bolt open after the last shot. MatalForm brand seem to be the most common, but there are a few companies making them now.

  4. #4
    www.aztecharmory.ca
    Join Date
    Dec 2014
    Location
    Penticton BC
    Posts
    330
    As some of you are aware, we were delayed a bit on the QC10 receivers. The CFO denied our initial application for an FRT number due to the fact that they were milled as "low shelf", meaning they would accept a DIAS which unfortunately is not allowed here.
    With that said, many thanks to QC10 for recognizing the value of the Canadian market and re-tooling to make a high shelf version just for us. We now have the FRT number and are bringing some lowers in on our August import. As of now, all but one Glock Large Frame are spoken for but we are happy to take orders for the September import.
    Thanks again to all of you who have been patient with us through the process.
    It's Not Always a Matter of Need...

  5. #5
    Senior Member Mark-II's Avatar
    Join Date
    Mar 2014
    Location
    Winnipeg
    Posts
    6,014
    Interesting. The 5 round limit of the Uzi mags made a 9mm pistol carbine a non starter for me before this

  6. #6
    www.aztecharmory.ca
    Join Date
    Dec 2014
    Location
    Penticton BC
    Posts
    330
    Check out QC10 on Instagram https://instagram.com/p/6Pw86rNJwQ/
    It's Not Always a Matter of Need...

  7. #7
    www.aztecharmory.ca
    Join Date
    Dec 2014
    Location
    Penticton BC
    Posts
    330
    Quote Originally Posted by Mark-II View Post
    Interesting. The 5 round limit of the Uzi mags made a 9mm pistol carbine a non starter for me before this
    The GSF is the way to go. These are very well made receivers with all small proprietary part included. You will want to get the glock cut bolt with it for last round hold open. We have barrels available too... check out www.quartercircle10.com
    It's Not Always a Matter of Need...

  8. #8
    www.aztecharmory.ca
    Join Date
    Dec 2014
    Location
    Penticton BC
    Posts
    330
    Success!! QC10 Lowers are officially here in Canada. Thanks to all who have ordered and waited. Your patience is very much appreciated.
    It's Not Always a Matter of Need...

  9. #9
    Junior Member
    Join Date
    Jul 2014
    Location
    oil patch
    Posts
    14
    Pics says it all, THANK YOU Marshall!! as always.









    the fake suppressor is temporary, acting as a thread protector until I find a suitable good looking 9mm flash hider.
    the fake Spike's suppressor is also meant to be slip on over the barrel, but the bull barrel profile is to thick so I just turned it around.






  10. The Following 2 Users Like This Post By Familygunnutz

    ESnel (04-02-2016), Marshall (09-10-2015)

  11. #10
    Junior Member
    Join Date
    Jul 2014
    Location
    oil patch
    Posts
    14
    a Small note, this is from Chris from QC10

    "Hello Ben,

    Our bolt does not work with the 3 gun triggers from geissele. Most of their triggers simply don't work in these blowback bolts the spring to reset the hammer is far too heavy and the hammer profile does not match up to the ramping of the bolts well. If you're looking for a nice trigger talk to someone at CMC triggers for their 3.5 that I know people are using on these Pistol Caliber Carbines.

    Chris
    QC10 "

    so guys make sure you don't use the geissele triggers when using any 9mm ramped bolts, any milspec or CMC triggers are gtg.

    oh btw, KIC 33rd mag absolutely DOES NOT work with this lower lol glock factory mags are solid.
    Last edited by Familygunnutz; 08-29-2015 at 01:41 AM.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •