PDA

View Full Version : HOW TO: SKS-AR Mag Adapter Install Guide & Pics.



hical.ca
05-15-2015, 10:34 AM
We wanted to let you know, these Mag adapters are available on our website now, HERE. (http://www.hical.ca/sks-ar-magwell-adapter/) We wanted to do a AR-SKS Mag Adapter Install Guide & Pics to help everyone out. We will do a video after the weekend, but wanted to post a guide for all those who already have one to install. Here is a conversion, step by step:

First we Make sure the gun is UNLOADED! Remember the ACTS & PROVE? Remove some metal from the front of the receiver for clearance, shown is one side done, the other untouched:

http://i629.photobucket.com/albums/uu12/mp5k1/058_zpshkvfoazu.jpg (http://s629.photobucket.com/user/mp5k1/media/058_zpshkvfoazu.jpg.html)


Both sides done, note how the front is cut almost to the bevel:


http://i629.photobucket.com/albums/uu12/mp5k1/059_zpsk47q24nf.jpg (http://s629.photobucket.com/user/mp5k1/media/059_zpsk47q24nf.jpg.html)

Next, see those trigger bars? we need to shorten them to clear the new mag:

http://i629.photobucket.com/albums/uu12/mp5k1/061_zpsy6dilser.jpg (http://s629.photobucket.com/user/mp5k1/media/061_zpsy6dilser.jpg.html)

Ta Da.....

http://i629.photobucket.com/albums/uu12/mp5k1/063_zpsguq3odql.jpg (http://s629.photobucket.com/user/mp5k1/media/063_zpsguq3odql.jpg.html)

Test fit the mag to make sure there is clearance:

http://i629.photobucket.com/albums/uu12/mp5k1/064_zpsamrhtleh.jpg (http://s629.photobucket.com/user/mp5k1/media/064_zpsamrhtleh.jpg.html)

You will also need to shorten the bolt hold open device by about 2-3 mm:

http://i629.photobucket.com/albums/uu12/mp5k1/026_zpsupziybjs.jpg (http://s629.photobucket.com/user/mp5k1/media/026_zpsupziybjs.jpg.html)

Then trim the front silver mount to fit your gun, I mark it with a sharpie, then trim:

http://i629.photobucket.com/albums/uu12/mp5k1/067_zpsj1nncazf.jpg (http://s629.photobucket.com/user/mp5k1/media/067_zpsj1nncazf.jpg.html)

Install & test, the bolt hold open should work, it should drop free:

http://i629.photobucket.com/albums/uu12/mp5k1/070_zpskeapngvp.jpg (http://s629.photobucket.com/user/mp5k1/media/070_zpskeapngvp.jpg.html)

Open up your stock to clear & hit the range, or 3 gun....


http://i629.photobucket.com/albums/uu12/mp5k1/059_zpsxyu9auxk.jpg (http://s629.photobucket.com/user/mp5k1/media/059_zpsxyu9auxk.jpg.html)

NOTE, you can still use your original factory mag or any aftermarket detachable mags still after this conversion, the adapter just pops out!

Canada_Phil
05-15-2015, 11:19 AM
Hey, that doesn't look too tough.
:)

Haywire1
07-04-2015, 06:49 PM
Will you be including the machining dimensions with the purchase of an adapter? How much depth is required on the front of the reciever for starters.